“地暖安装规范”参数说明
是否有现货: | 是 | 颜色: | 多色 |
特殊功能: | 防水 | 风格: | 现代 |
图案: | 纯色 | 地板厚度: | 10mm |
型号: | 已认证 | 规格: | 已认证 |
商标: | 已认证 | 包装: | 已认证 |
“地暖安装规范”详细介绍
1、地暖施工工艺:边角保温铺设
1, to warm the construction process: corner insulation laying
边角保温铺设地带地面与墙面夹角应清理干净。边角保温采用高发泡PE聚乙烯保温材料,厚10mm,高度为60mm,沿外墙四周铺设,并用绝热层挤塑板挤牢。
济南爱皮人沙发维修中心 http://www.jnshafaweixiu.com 济南沙发维修 济南沙发翻新
Corner insulation laying ground and wall angle should be cleaned. Corner insulation adopts PE high foaming polyethylene insulation material, thickness 10mm, height 60mm, laying along the exterior walls, and insulation board extrusion.
2、地暖施工工艺:铺设保温板
2, to warm the construction process: insulation board
按照施工图铺设保温板,紧密铺设,并将铝箔铺设完毕后用胶带粘牢。
According to the construction drawings of the insulation board, close laying, and aluminum foil after laying taped.
3、地暖施工工艺:管路铺设
3 the heating pipe laying construction process.
严格按照设计施工图纸铺设加热管,并用塑料卡钉按照图纸将管材固定于挤塑板上或用绑带固定在钢丝网上。
In strict accordance with the design drawings of laying heating pipe, and a plastic card for use in accordance with the drawings will be fixed on the screw pipe extruded board or fixed on the steel wire net with a bandage.
4、地暖施工工艺:安装分集水器
4, to warm the construction process: diversity water device installation
将分集水器水平安装于图纸指定位置,分水器于上集水器于下,间距200mm,集水器中心距地面高度不小于300mm。(如分集水器垂直安装 则分、集水器下端距地面应不小于150mm)考虑装修,背面应预留30mm。
The level of diversity water device installation location specified in the drawings on the collector in the water separator, spacing of 200mm, the collector center height from the ground is not less than 300mm. (such as diversity water device installed vertically is divided, the collector is apart from the ground should not be less than 150mm) consider the decoration, the back should be reserved for 30mm.
1, to warm the construction process: corner insulation laying
边角保温铺设地带地面与墙面夹角应清理干净。边角保温采用高发泡PE聚乙烯保温材料,厚10mm,高度为60mm,沿外墙四周铺设,并用绝热层挤塑板挤牢。
济南爱皮人沙发维修中心 http://www.jnshafaweixiu.com 济南沙发维修 济南沙发翻新
Corner insulation laying ground and wall angle should be cleaned. Corner insulation adopts PE high foaming polyethylene insulation material, thickness 10mm, height 60mm, laying along the exterior walls, and insulation board extrusion.
2、地暖施工工艺:铺设保温板
2, to warm the construction process: insulation board
按照施工图铺设保温板,紧密铺设,并将铝箔铺设完毕后用胶带粘牢。
According to the construction drawings of the insulation board, close laying, and aluminum foil after laying taped.
3、地暖施工工艺:管路铺设
3 the heating pipe laying construction process.
严格按照设计施工图纸铺设加热管,并用塑料卡钉按照图纸将管材固定于挤塑板上或用绑带固定在钢丝网上。
In strict accordance with the design drawings of laying heating pipe, and a plastic card for use in accordance with the drawings will be fixed on the screw pipe extruded board or fixed on the steel wire net with a bandage.
4、地暖施工工艺:安装分集水器
4, to warm the construction process: diversity water device installation
将分集水器水平安装于图纸指定位置,分水器于上集水器于下,间距200mm,集水器中心距地面高度不小于300mm。(如分集水器垂直安装 则分、集水器下端距地面应不小于150mm)考虑装修,背面应预留30mm。
The level of diversity water device installation location specified in the drawings on the collector in the water separator, spacing of 200mm, the collector center height from the ground is not less than 300mm. (such as diversity water device installed vertically is divided, the collector is apart from the ground should not be less than 150mm) consider the decoration, the back should be reserved for 30mm.